Taylor-Dunn AN 171 Скачать руководство пользователя

Страница: 96 / 206

Curtis PMC Troubleshooting

Page 2

REV

FWD

Solenoids

PMC Speed Control

Circuit Breaker

ISO

Typical Control Panel

SYMPTOMS:

If your vehicle exhibits any of the following symptoms then skip the main troubleshooting

sequence and proceed to

Symptom Troubleshooting

later in this section.

• Runs slow in both directions plus high armature and field current in both directions. NOTE:

Armature and field current should be equal.

•

Runs slow in both directions plus high armature current in both directions. NOTE: Field

current will be very low.

•

Runs normal in one direction only plus runs slow or lacks power in the opposite direction

with high armature current in the opposite direction or;

•

Accelerates slowly and exceeds normal speed in the opposite direction with high armature

current only. NOTE: Field current will be very low in the opposite direction.

•

Accelerates slowly and exceeds normal speed in both directions plus high armature current.

NOTE: Field current will be very low.

•

Full speed only.

• Does not run in either direction plus there is noise from motor (hum or whine) with high

field current and low armature current.

•

Jumps into high speed when direction is selected after depressing the accelerator pedal.

Excessive spark when connecting battery

•

Does not run or runs very slow with low motor current and high battery current.

•

Jumps into high speed when direction is selected after depressing the accelerator pedal.

If your vehicle does not exhibits any of the above symptoms then continue with the main

troubleshooting sequence on the following pages.

Note: Vehicles with Dana H12 transmission,
Forward solenoid is in the center.

Содержание AN 171















































































































































































































Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды

Taylor-Dunn AN 171, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды