Taylor-Dunn AN 171 Скачать руководство пользователя

Страница: 138 / 206

Electrical Troubleshooting

Signet Charger Troubleshooting
Page 4

TEST EQUIPMENT REQUIRED FOR TROUBLESHOOTING

Digital Multi Meter (DMM), FLUKE 79

model shown at right and in the troubleshooting

illustrations.
Clamp on DC ammeter to measure up to 20-Amps.

Important Notes and Instructions

• This troubleshooting guide assumes a familiarity with the use of a digital multimeter

including, voltage tests, continuity tests and diode testing. If not familiar with

any part of these tests, refer testing to a qualified technician.

• Make sure that the AC electrical socket the charger is plugged into is in good

working condition.

• Make sure that the AC voltage at the electrical socket is the same as the AC

voltage on the charger nameplate.

• Make sure the batteries are in good condition.

• If the charger exhibits intermittent problems, it must be in the failed mode for troubleshooting.

• Battery volts = Full voltage available at the batteries at the time of the test being performed.

• There are no internally serviceable components in the charger. If the charger has failed then it must be

replaced.

A Y

L OR - DUN

Go About

This charger is rated for 115 VAC or 230 VAC operation. When switching

from one input voltage to the other, wait until all three status LED’s

are off. Switching voltage when any of the LED’s are on will result in

damage to the charger.

Содержание AN 171















































































































































































































Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды

Taylor-Dunn AN 171, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды