swaploader SL-212 Скачать руководство пользователя страница 8

Страница: 8 / 88

III. CONTROLS

Controls easy to operate from driver

’s seat.

Movement of controls correct, per installation instructions.

IV. HYDRAULIC INSTALLATION

Correct hydraulic oil level in reservoir, per installation instructions.

Inspected for leaks.

Any abnormal noise during hoist operation?

YES

If yes, please describe:

With engine operating @ 1,000 RPM, record the following information:

Cycle time for dump mode:

Seconds Up

Seconds Down

Cycle time for load/unload mode:

Seconds to Unload Seconds to Load

Filter pressure:

PSI

Main pressure, controls in neutral:

PSI

Main relief pressure when extending

jib cylinder (bottomed out):

PSI

Main relief pressure when extending

lift cylinders (bottomed out):

PSI

NOTE:

V. OPERATION

Jib operates freely in both directions.

Jib cannot be extended or retracted when raised in dump position or when pivot joint is tilted in unload position.
Both safety hooks are fully engaged when jib is extended.

Parts & Operations Manual is in the cab.

Lubricate sliding jib and all grease zerks per installation instructions.

VI. DECALS

All safety decals and product decals installed per enclosed decal drawings (found attached to the inside of the

hoist

’s Parts & Operations Manual cover or at the back of the Parts List section in the Manual).

Additional Comments:

COMPLETE & SAVE TO YOUR COMPUTER. RETAIN A COPY FOR YOUR FILES.

ONCE COMPLETE, FAX (515-313-4426) OR EMAIL ([email protected]) A COPY BACK TO SWAPLOADER!

Содержание SL-212

























































































Результаты поиска

Содержание SL-212

Отзывы:

Похожие инструкции для SL-212

Бренды по названию

Популярные бренды

swaploader SL-212, Руководство по эксплуатации и частям

Результаты поиска

Содержание SL-212

Отзывы:

Похожие инструкции для SL-212

Бренды по названию

Популярные бренды