swaploader SL-212 Скачать руководство пользователя страница 7

Страница: 7 / 88

SWL-869 SWAPLOADER 11/13

PRE-DELIVERY CHECK LIST

INSPECTOR

’S INFORMATION

Inspected By:

Distributor:

Customer:

Signature:

Date Installed:

Date Inspected:

COMPONENT INFORMATION

Hoist Model:

Hoist Serial No.:

Chassis VIN:

Chassis Make & Model:

Chassis GVWR:

Chassis CA / CT:

After Frame:

PTO Make:

PTO Model:

PTO Serial No.:

PTO % of Engine RPM:

Hyd. Pump Make:

Hyd. Pump Model:

Hyd. Pump Serial No.:

Distance from rear of cab to the
centerline of rear axle/tandem.
Distance from centerline of rear
axle/tandem to rear of hoist.

II. INSTALLATION TO CHASSIS

Were there any problems installing the hoist to the truck chassis?

YES

If yes, please describe:

All bolts checked for proper tightness.

Please include photos of the hoist installed on the truck chassis.
Be sure to include at least one photo from each side of the chassis/hoist.

Содержание SL-212

























































































Результаты поиска

Содержание SL-212

Отзывы:

Похожие инструкции для SL-212

Бренды по названию

Популярные бренды

swaploader SL-212, Руководство по эксплуатации и частям

Результаты поиска

Содержание SL-212

Отзывы:

Похожие инструкции для SL-212

Бренды по названию

Популярные бренды