swaploader SL-212 Скачать руководство пользователя страница 51

Страница: 51 / 88

Section III: Operation

3.0.OPE.SL-212

PLACING A CONTAINER ON THE GROUND:

STEP 1.

Move the sliding jib all the way back (right control backward) until mechanical jib latches unlock.

STEP 2.

Tilt the arm backwards (left control backward). When the container touches the ground, release
the brakes to free the truck for forward movement caused by the container.

STEP 3.

Rotate jib all the way back until the container touches the ground. Pull away from container and
rotate jib back into the transport position.

WARNING:

1. DON'T OVER SPEED THE PUMP 1,500 RPM

MAXIMUM.

2. DON'T DUMP, MOUNT OR DISMOUNT BODIES

ON UNEVEN GROUND.

DON'T DRIVE WITH THE HOIST IN THE DUMP
POSITION OR WITH THE HOOK TILTED BACK.

3-3

Содержание SL-212

























































































Результаты поиска

Содержание SL-212

Отзывы:

Похожие инструкции для SL-212

Бренды по названию

Популярные бренды

swaploader SL-212, Руководство по эксплуатации и частям

Результаты поиска

Содержание SL-212

Отзывы:

Похожие инструкции для SL-212

Бренды по названию

Популярные бренды