swaploader SL-212 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 88

background image

Section II: Installation

2.0.INS.SL-212

locally or through SwapLoader.  Take proper care when routing the control cables, as a
good cable path is essential for a proper operating system.  Keep bends in the cable
path to a minimum and be as generous as possible.  Under no circumstances should
any bend be tighter than an 8" radius.  Protect the cable from heat above 225 degrees F.
and avoid hot areas such as exhaust pipes, etc. Protect the cable from physical
damages such as pinching or crushing, and do not use cable supports, which may crush
or deform the cable.  Allow room for flexing where the cable is attached to moving parts
of the equipment, so that the cable is neither kinked nor stretched.

INSTALLATION PROCEDURE FOR A HYDRAULIC CONTROL CABLE TO

HYDRAULIC VALVE WITH BONNET CONNECTION KIT

1. Turn .750-16 UNF jam nut entire length of threaded hub back over the cable. Place

Flange onto Sleeve (large end first) and flange onto sleeve and turn flange adaptor /
flange / sleeve assembly entire length of threaded hub back over the cable.

2. Turn .250-28 UNF jam nut onto cable threaded rod until it bottoms.
3. Place clevis of threaded rod and bottom against jam nut. Turn other .250-28 UNF jam

nut onto threaded rod until it bottoms against clevis. Align clevis so it will mate with
spool terminal eye and secure jam nut against clevis.

4. Slide the clevis onto terminal eye on spool and align the holes. Insert clevis pin through

yoke and terminal eye holes and secure clevis pin with retaining ring.

5. Now, with the cable attached to the valve and control head, turn the flange adapter /

flange / sleeve assembly back onto the threaded hub until it is flush with the valve face.
When turning on the flange adapter / flange / sleeve assembly, make sure that the
control head remains in the neutral position.

6. Tighten the .750-16 UNF jam nut against the sleeve and lock in position.
7. Bring flange into position on bolt assembly to valve housing.

Figure G

2-5

«
...
21
22
23
24
25
...
»

Содержание SL-212

























































































Отзывы:

Нет отзывов

Похожие инструкции для SL-212

Бренд: KAR-TECH Страницы: 28

Бренд: National Instruments Страницы: 23

Бренд: Waterway Страницы: 8

GreenCable Mat Series

Бренд: Flextherm Страницы: 20

Бренд: Nalnor Страницы: 8

Бренд: 2VV Страницы: 29

Бренд: Northern Industrial Tools Страницы: 18

POWER2 S-CUTTER 50.1

Бренд: STAMOS Страницы: 41

Aqua-Hot AHE-100-02S

Бренд: Vehicle Systems Страницы: 24

Бренд: Jasic Страницы: 21

Protecta series

Бренд: 3M Страницы: 16

Бренд: Fronius Страницы: 92

MONOGYS 200-2CS

Бренд: GYS Страницы: 55

HIGHLANDER EPL400

Бренд: Harmar Mobility Страницы: 32

Бренд: YATO Страницы: 16

Opto-Matic 30078

Бренд: Trico Страницы: 2

100SG SPOOL GUN

Бренд: Magnum Страницы: 13

MIG200L PRO DUAL PULSE

Бренд: Magnum Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды