swaploader SL-212 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 88

background image

Section II: Installation

2.0.INS.SL-212

Measure1-3/16” from the end of the hose and mark the hose for the socket depth.
Screw hose into the socket (left-hand thread) to the depth marked on the hose.  Screw
insert in socket until insert touches the socket.  Clean the inside of the hose assembly by
either blowing clean compressed air through it or by flushing it.  Install the completed
hose assembly to the inlet port of the control valve assembly and the outlet port of the
hydraulic pump.

5. Tie up the pressure and suction hoses as necessary. Again, be sure the hoses are

routed to avoid exhaust components and to stay clear of the drive shaft.

START UP PROCEDURE

1. Fill the hydraulic tank with hydraulic oil (see oil specification in Section IV: Maintenance.)
2. Prime the pump by loosening the clamp on the suction hose at the pump. Pull the hose

back off the fitting till the air is bled from the line. Push the hose back on the fitting and
retighten the clamp.

3. Engage the P.T.O. and run the engine at idle (700 to 900 RPM). Operate the cylinders

at full stroke five to ten times to bleed the air from the lines and cylinders. The cylinders
were filled with oil during testing at the factory, but some seepage may have occurred
during shipping and installation. Refill the hydraulic tank, if needed, during this
sequence and do not let the pump run without oil.

4. Check for leaks and tighten fittings as

necessary.

5. Verify the movement of the control levers

corresponds to the movement of the
cylinders per the figure below.

6. Install all safety decals and product

decals as shown on

Pg. 1-5

after final

installation and painting have been
completed.

7. Fill out pre-delivery checklist and

warranty card and email to SwapLoader
U.S.A., Ltd.

NOTE:

FAILURE TO FILL OUT AND RETURN WARRANTY CARD WITHIN 15 DAYS OF INSTALLATION MAY POSSIBLY VOID
THE WARRANTY.

CAUTION The SwapLoader hoist must be used with bodies or containers that properly

fit the front hook and the rear hold-downs (see Subframe Critical Dimensions
on Pgs. 2-12 & 2-13). If possible, pick up one of the containers that will
actually be used with the SwapLoader hoist and verify the following:



Outside dimensions of the long sills match the guiding rollers on the
hoist.



The front hook dimensions are correct for the hoist.



The rear hold-downs of the container latch into the hold-downs on
the hoist.



Check for any interference between the container and any part of the
hoist (i.e.: Hydraulic tank, hydraulic tubing or hose, hydraulic valve,
etc.)

2-9

«
...
25
26
27
28
29
...
»

Содержание SL-212

























































































Отзывы:

Нет отзывов

Похожие инструкции для SL-212

Бренд: EAE Страницы: 36

Бренд: First Power Страницы: 16

Бренд: Jet Страницы: 40

Бренд: National Instruments Страницы: 297

Бренд: ICP DAS USA Страницы: 4

Бренд: Artila Страницы: 15

Бренд: Haklift Страницы: 32

JFLEX-Visualisation1

Бренд: Kontron Страницы: 19

Бренд: Ravaglioli Страницы: 60

Бренд: Fenix Страницы: 24

Panelovn Zigbee

Бренд: Namron Страницы: 11

Бренд: INVERTEC Страницы: 36

Бренд: Dahua Technology Страницы: 10

PRO-POWER VIMSF100

Бренд: VITO Страницы: 48

Бренд: National Instruments Страницы: 49

Бренд: Chicago Electric Страницы: 24

Бренд: Hitachi Страницы: 242

Бренд: IFM Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды