manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Руководство по обслуживанию


Поделиться
Скачать
background image

Immobilizer Control System:  10C-17

DTC P1638: Immobilizer Information Mismatched

S5JB0EA304017

Wiring Diagram
Refer to “Immobilizer Control System Wiring Circuit Diagram: ”

DTC Detecting Condition and Trouble Area

Troubleshooting

Detecting Condition

Trouble Area

• The immobilizer control system information in ECM and 

the one in BCM does not match.

• The registration of the immobilizer control system 

information in ECM is failed.

• Use of the wrong ECM

• Steering angle sensor (if equipped) faulty

• Keyless start control module (if equipped) faulty

• 4WD control module (if equipped)

• TCM (if equipped) faulty

• CAN communication wire circuits faulty

• BCM faulty

• Combination meter faulty

• ABS/ESP

®

 control module faulty

• ECM faulty

Step

Action

Yes

No

1

Diagnostic Trouble Code (DTC) confirmation

1) Clear DTC(s) referring to “Diagnostic Trouble Code 

(DTC) Clearance:  in related manual”.

2) Turn the ignition switch to OFF position.

3) Check if any DTC is detected referring to “Diagnostic 

Trouble Code (DTC) Check:  in related manual”.

Is DTC P1638 still detected?

Go to Step 2.

The troubleshooting is 
completed.

2

Diagnostic Trouble Code (DTC) confirmation

1) Disconnect negative (–) cable from battery for more than 

5 seconds.

2) Connect negative (–) cable to battery.

3) Check if any DTC is detected referring to “Diagnostic 

Trouble Code (DTC) Check:  in related manual”.

Is DTC P1638 still detected?

Go to Step 3.

The troubleshooting is 
completed.

3

Check ECM specification

1) Check ECM part number to see if ECM is applicable to 

the vehicle in service.

Is a correct ECM used for the vehicle in service?

Go to Step 2.

Replace ECM with the 
correct one and recheck 
if DTC P1638 is still 
detected by ECM.

4

Diagnostic Trouble Code (DTC) check in ECM

Is any DTC other than P1638 detected in Step 1?

Perform the 
troubleshooting 
referring to the 
corresponding 
flowchart.

Go to Step 3.

5

Diagnostic Trouble Code (DTC) check in BCM

1) Check BCM for DTC referring to “DTC Check:  in 

Section 10B in related manual”.

Is any DTC detected?

Perform the 
troubleshooting 
referring to the 
corresponding flowchart 
in Section 10B.

Go to Step 5.

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA JB416

Jeep 2009 Wrangler Quick Reference Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 12
Jeep 2008 Liberty Installation Instructions Manual preview
2008 Liberty
Бренд: Jeep Страницы: 6
Yakima KingJoe 2 Quick Start Manual preview
KingJoe 2
Бренд: Yakima Страницы: 7
Yakima BowDown Quick Start Manual preview
BowDown
Бренд: Yakima Страницы: 6
Yakima LOCKN'LOAD Manual preview
LOCKN'LOAD
Бренд: Yakima Страницы: 10
Yakima HitchSki Quick Start Manual preview
HitchSki
Бренд: Yakima Страницы: 12
RAM Ram 3500 2012 User Manual preview
Ram 3500 2012
Бренд: RAM Страницы: 116
Velleman CAMCOLC1N User Manual preview
CAMCOLC1N
Бренд: Velleman Страницы: 6
Thule 1511 Instructions Manual preview
1511
Бренд: Thule Страницы: 8
TATA Motors tigor Owner'S Manual preview
tigor
Бренд: TATA Motors Страницы: 159
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Бренд: Honda Страницы: 85
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Бренд: Audiovox Страницы: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Бренд: Mercedes-Benz Страницы: 2
Westin 25-0560 Instructions preview
25-0560
Бренд: Westin Страницы: 2
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Бренд: Menabo Страницы: 8
Pontiac 2006 Relay Getting To Know Manual preview
2006 Relay
Бренд: Pontiac Страницы: 20
ORA XL MIRROR Installation Instructions Manual preview
XL MIRROR
Бренд: ORA Страницы: 7
GMC 2008 Savana Van Owner'S Manual preview
2008 Savana Van
Бренд: GMC Страницы: 402

Бренды по названию

Популярные бренды

Загрузить еще бренды