manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-23 Automatic Transmission/Transaxle: 

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Connect scan tool to DLC with ignition switch turned OFF.

2) Turn ON ignition switch and clear DTC by using scan tool.

3) Start engine and run it for 1 min. or more.

4) Check DTC and pending DTC.

DTC Troubleshooting

NOTE

Upon completion of inspection and repair work, perform “DTC Confirmation Procedure: ” and confirm 
that the trouble has been corrected.

 

DTC Detecting Condition

Trouble Area

Transmission error that is inconsistent between transmission data 
and transmission monitor (CAN bus monitor) data is detected more 
than 7 times continuously.
(1 driving cycle detection logic)

• ECM

• TCM

• Combination meter

• BCM

• ABS/ESP

®

 control module

• Steering angle sensor (if equipped)

• 4WD control module (if equipped)

• Keyless start control module (if equipped)

• CAN communication line circuit

Step

Action

Yes

No

1

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System 
Check:  in related 
manual”.

2

Control module connector check

1) Check connection of connectors of all control modules 

communicating by means of CAN.

2) Recheck DTC in TCM referring to “DTC Check:  in 

related manual”.

Is there DTC P1774?

Go to Step 3.

Intermittent trouble. 
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00 in related manual”.

3

CAN communication circuit check

1) Turn ignition switch to OFF position.

2) Disconnect connectors of all control modules 

communicating by means of CAN.

3) Check CAN communication circuit between control 

modules for open, short and high resistance.

Is each CAN communication circuit in good condition?

Go to Step 4.

Repair circuit.

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA JB416

LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Бренд: RAM Commercial Страницы: 12
FORM FIT 1303 Installation Instructions preview
1303
Бренд: FORM FIT Страницы: 2
WABCO TP2205 Installation Manual preview
TP2205
Бренд: WABCO Страницы: 48
Pontiac 2004 Vibe Navigation System Owner'S Manual preview
2004 Vibe Navigation System
Бренд: Pontiac Страницы: 44
Maserati Gransport Owner'S Manual preview
Gransport
Бренд: Maserati Страницы: 210
OnStar liveon Owner'S Manual preview
liveon
Бренд: OnStar Страницы: 22
Maserati Quattroporte Automatic Owner'S Manual preview
Quattroporte Automatic
Бренд: Maserati Страницы: 272
Meta System 900000358 Installation Technical Sheet preview
900000358
Бренд: Meta System Страницы: 22
rockymounts SplitRailLS Installation Instructions Manual preview
SplitRailLS
Бренд: rockymounts Страницы: 6
BrandMotion FLTW-7511 Installation Manual preview
FLTW-7511
Бренд: BrandMotion Страницы: 6
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Бренд: INDIWORK Страницы: 18
Opel CORSA 2020 Infotainment Manual preview
CORSA 2020
Бренд: Opel Страницы: 103
N-Com Bluetooth Kit3 PLUS User Instructions And Safety preview
Bluetooth Kit3 PLUS
Бренд: N-Com Страницы: 36
Ferve F-2024 Operating Instructions Manual preview
F-2024
Бренд: Ferve Страницы: 28
BraunAbility Rampvan Maintenance And Service Manual preview
Rampvan
Бренд: BraunAbility Страницы: 46
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Бренд: Brodit Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды