Suzuki GRAND VITARA JB416 Скачать руководство пользователя страница 169

Страница: 169 / 474

Transfer: Motor-Shift Type (Transfer with Shift Actuator) 3C-52

DTC U1121: Lost Communication with ABS / Electronic Stability Program Hydraulic Unit / Control
Module

S5JB0E3314029

Wiring Diagram
Refer to “DTC U1073: Control Module Communication Bus Off: Motor-Shift Type (Transfer with Shift Actuator)”.

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Clear DTC using scan tool.

2) Start engine and run it for 1 min. or more.

3) Stop vehicle and check DTC.

Troubleshooting

DTC detecting condition

Trouble area

Reception error of communication data for ABS or ESP

hydraulic unit / control module is detected for longer than
specified time continuously.

• CAN communication circuit

• ABS or ESP

hydraulic unit / control module

• 4WD control module

Step

Action

Yes

Was “4WD control system check” performed?

Go to Step 2.

Go to “4WD Control
System Check: Motor-
Shift Type (Transfer with
Shift Actuator)”.

DTC check

1) Check DTC in 4WD control module.

Is DTC U1100 and DTC U1073 detected together?

Go to “DTC U1073:
Control Module
Communication Bus
Off: Motor-Shift Type
(Transfer with Shift
Actuator)”.

Go to Step 3.

DTC check

1) Check DTC in ABS or ESP

hydraulic unit / control

module.

Is DTC U1073 detected?

Go to “DTC U1073:
Control Module
Communication Bus
Off: in Section 4E”.

Go to Step 4.

Check each control module connectors

1) Check connection of connectors of all control modules

communicating by means of CAN.

2) Recheck in 4WD control module.

Is DTC U1100 detected?

Go to Step 5.

Intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection: in Section
00 in related manual”.

CAN communication circuit check

1) Turn ignition switch to OFF position.

2) Disconnect connectors of all control modules

communicating by means of CAN.

3) Check CAN communication circuit between control

modules for open, short and high resistance.

Is each CAN communication circuit in good condition?

Check ABS or ESP

hydraulic unit / control
module power and
ground circuit. If circuit
is OK, substitute a
known-good ABS or
ESP

hydraulic unit /

control module and
recheck.

Repair circuit.

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Результаты поиска

Содержание GRAND VITARA JB416

Отзывы:

Похожие инструкции для GRAND VITARA JB416

Бренды по названию

Популярные бренды

Suzuki GRAND VITARA JB416, Руководство по обслуживанию

Результаты поиска

Содержание GRAND VITARA JB416

Отзывы:

Похожие инструкции для GRAND VITARA JB416

Бренды по названию

Популярные бренды