Suzuki GRAND VITARA JB416 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 474

background image

1A-42 Engine General Information and Diagnosis:

DTC P1685: CAN Communication (Reception Error for ABS or ESP

®

Control Module)

S5JB0E1104067

Wiring Diagram
Refer to “DTC P1674: CAN Communication (Bus Off Error): ”.

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Connect scan tool to DLC with ignition switch turned OFF.

2) Turn ON ignition switch and clear DTC by using scan tool.

3) Start engine and run it for 1 min. or more.

4) Check DTC.

DTC Troubleshooting

NOTE

Before this trouble shooting is performed, read the precautions for DTC troubleshooting referring to
“Precautions For DTC Troubleshooting: in related manual”.

17

Combination meter operation check

1) Check combination meter operation for seat belt warning

lamp by fastening and unfastening driver side seat belt
with ignition switch turned ON.

Is it check result satisfactory?

Substitute a known-
good ECM and recheck.

Check BCM power and
ground circuits, If
circuits are OK,
substitute a known-
good BCM and recheck.

Step

Action

Yes

No

DTC detecting condition

Trouble area

Reception error of communication data for ABS or ESP

®

control module is detected for longer than specified time
continuously.
(1 driving detection logic)

• ECM

• ABS or ESP

®

control module

• CAN communication line circuit

Step

Action

Yes

No

1

Was “Engine and Emission Control System Check”
performed?

Go to Step 2.

Go to “Engine and
Emission Control
System Check: in
related manual”.

2

DTC check

1) Connect scan tool to DLC with ignition switch turned

OFF.

2) Check ECM, TCM (for A/T model), ABS / ESP

®

control

module, 4WD control module (if equipped), keyless start
control module (if equipped) and BCM for DTC.

Is there any DTC(s) other than CAN communication DTC(s)
at each control module (other than DTC P1618, P1674,
P1676, P1678, P1685 in ECM, DTC P1774, P1777, P1778
in TCM (for A/T model), DTC U1073, U1100, U1101, U1121,
U1126, U1139, U1140, U1144 in BCM, ABS / ESP

®

control

module and 4WD control module (if equipped), and DTC
No.31 / 33 in keyless start control module (if equipped))?

Go to applicable DTC
diag. flow.

Go to Step 3.

3

Check CAN communication error for ECM

1) Check ECM for DTC.

Is there DTC P1674?

Go to “DTC P1674:
CAN Communication
(Bus Off Error): ”.

Go to Step 4.

«
...
58
59
60
61
62
...
»

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA JB416

Бренд: J-Top Страницы: 2

Бренд: K&M Страницы: 3

Lippert Components LEVELEGS MPD 66385

Бренд: Atwood Страницы: 6

65 41 2 152 528

Бренд: BMW Страницы: 21

signal mirror 2005-2009 Ford Mustang

Бренд: muth Страницы: 9

Бренд: Chevrolet Страницы: 344

Бренд: Prorack Страницы: 15

Бренд: AA Products Страницы: 4

Бренд: Omix-Ada Страницы: 6

Бренд: Daesung Страницы: 9

Бренд: Pontiac Страницы: 318

Бренд: MULTILIFT Страницы: 62

Бренд: Horn Tools Страницы: 12

Бренд: Mitsubishi Страницы: 367

Бренд: Curt Group Страницы: 3

Бренд: Juna Страницы: 10

Бренд: Metra Electronics Страницы: 10

FUEL TANK GAUGE

Бренд: VDO Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды