manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Руководство по обслуживанию


Поделиться
Скачать
background image

1A-28 Engine General Information and Diagnosis: 

DTC P0500: Vehicle Speed Sensor (VSS) Malfunction

S5JB0E1104051

Wiring Diagram

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

WARNING

!

 

• When performing a road test, select a place where there is no traffic or possibility of a traffic 

accident and be very careful during testing to avoid occurrence of an accident.

• Road test should be carried out by 2 persons, a driver and a tester.

 

1) With ignition switch turned OFF, connect scan tool.

2) Turn ON ignition switch and clear DTC using scan tool.

3) Warm up engine to normal operating temperature.

4) Drive vehicle at 4000 rpm (engine speed) with 3rd gear (for M/T vehicle) or “3” range (for A/T vehicle).

5) Release accelerator pedal and with engine brake applied, keep vehicle coasting for 6 sec. or more (fuel cut 

condition for 5 sec. or more) and stop vehicle.

6) For A/T model, drive vehicle at more than 3700 rpm for 10 sec.

7) Check pending DTC and DTC.

E23-4

E23-19

WHT/RED

WHT/BLU

WHT/RED

WHT/BLU

E23

C37

3

4

18

19

5

6

7

10

11

17

20

47

46

49

50

51

21

22

52

16

25

9

24

14
29

55

57

54 53

59

60

58

2

26

27

28

15
30

56

48

32

31

34

35

36

37

40

42

39 38

44

45

43

41

33

1

12

13

23

8

3

4

18

19

5

6

7

10

11

17

20

47

46

49

50

51

21

22

52

16

25

9

24

14
29

55

57

54 53

59

60

58

2

26

27

28

15
30

56

48

32

31

34

35

36

37

40

42

39 38

44

45

43

41

33

1

12

13

23

8

BLK

WHT

BLK

WHT

YEL/BLK

YEL

LT GRN
LT GRN/BLK

12V

12V

1

2

3

4

I5JB0A110060-03

1. Rear left side wheel speed sensor (VSS 1)

3. ABS / ESP

®

 control module 

2. Rear right side wheel speed sensor (VSS 2)

4. ECM

DTC detecting condition

Trouble area

• Vehicle speed signal is not input while fuel is cut at 

deceleration for 4 seconds continuously at 3600 rpm or 
less.

• Vehicle speed signal is not input even if engine is running 

with more than 3700 rpm at D-Range for 4 sec. (for A/T 
model).

(2 driving cycle detection logic)

• Wheel speed sensor (VSS)

• Wheel speed sensor circuit 

• ABS / ESP

®

 control module

• ECM

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA JB416

Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Бренд: Genesis Страницы: 3
Mobis G4211ADE00AL Installation Instructions Manual preview
G4211ADE00AL
Бренд: Mobis Страницы: 16
Subaru starlink Manual preview
starlink
Бренд: Subaru Страницы: 216
Ford FIESTA ST 2019 Supplement Manual preview
FIESTA ST 2019
Бренд: Ford Страницы: 37
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Бренд: muth Страницы: 9
Subaru 2007 Impreza Brochure & Specs preview
2007 Impreza
Бренд: Subaru Страницы: 21
AA Products SR-A260 Instruction Manual preview
SR-A260
Бренд: AA Products Страницы: 4
Xblitz Mirror 2016 User Manual preview
Mirror 2016
Бренд: Xblitz Страницы: 30
TAUBENREUTHER 29-T080301 Quick Start Manual preview
29-T080301
Бренд: TAUBENREUTHER Страницы: 8
Caltrend BM110 Installation Instructions preview
BM110
Бренд: Caltrend Страницы: 2
Advanced ICE 1296-1 Manual preview
1296-1
Бренд: Advanced ICE Страницы: 4
Mercedes-Benz 2015 SLK Operator'S Manual preview
2015 SLK
Бренд: Mercedes-Benz Страницы: 358
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Бренд: Ecco Страницы: 24
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Бренд: Cadillac Страницы: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Бренд: TIE DOWN Страницы: 2
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Бренд: RAM Страницы: 330
true-i HMBS-200 User Manual preview
HMBS-200
Бренд: true-i Страницы: 11
Prime Design URX-001-E Assembly Instructions Manual preview
URX-001-E
Бренд: Prime Design Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды