Suzuki GRAND VITARA JB416 Скачать руководство пользователя страница 147

Страница: 147 / 474

Transfer: Motor-Shift Type (Transfer with Shift Actuator) 3C-30

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Clear DTC using scan tool.

2) Select transfer switch to “4H” position and keep its position for 10 seconds. Similarly select transfer switch to “4H-

lock”, “N” and “4L-lock” position.

3) Check DTC.

Troubleshooting

DTC detecting condition

Trouble area

Transfer switch combination different from specification is
detected for more than 0.5 seconds.

• Transfer switch

• Transfer switch circuit

• 4WD control module

Step

Action

Yes

Was “4WD control system check” performed?

Go to Step 2.

Go to “4WD Control
System Check: Motor-
Shift Type (Transfer with
Shift Actuator)”.

Transfer switch circuit check

1) Disconnect transfer switch connector “G59” with ignition

switch OFF.

2) Check for proper connection to “G59-2”, “G59-3” and

“G59-4” terminals of transfer switch connector.

3) If connection is OK, measure voltage between “G59-2”,

“G59-3” or “G59-4” terminal of transfer switch connector
and vehicle body ground with ignition switch ON.

Is it 10 – 14 V?

Go to Step 3.

Go to Step 4.

Transfer switch check

1) Check transfer switch referring to “Transfer Switch

Inspection: Motor-Shift Type (Transfer with Shift
Actuator)”.

Is switch in good condition?

Substitute a known-
good 4WD control
module and recheck.

Replace transfer switch.

Wire harness check

1) Disconnect connector from 4WD control module

connector “E91” with ignition switch OFF.

2) Check for shorted to ground in related circuits.

• Between “G59-2” terminal of transfer switch connector

and “E91-18” terminal of 4WD control module
connector

• Between “G59-3” terminal of transfer switch connector

and “E91-19” terminal of 4WD control module
connector

• Between “G59-4” terminal of transfer switch connector

and “E91-20” terminal of 4WD control module
connector

Are they in good condition?

Substitute a known-
good 4WD control
module and recheck.

Repair circuit.

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Результаты поиска

Содержание GRAND VITARA JB416

Отзывы:

Похожие инструкции для GRAND VITARA JB416

Бренды по названию

Популярные бренды

Suzuki GRAND VITARA JB416, Руководство по обслуживанию

Результаты поиска

Содержание GRAND VITARA JB416

Отзывы:

Похожие инструкции для GRAND VITARA JB416

Бренды по названию

Популярные бренды