manualshive.com logo in svg

Suzuki GRAND VITARA JB416, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission/Transaxle:  5A-28

DTC Troubleshooting

Step

Action

Yes

No

1

Vehicle speed signal check

1) Check DTC in ECM and ABS/ESP

®

 control module 

referring to “DTC Check:  in Section 1A in related 
manual” or “DTC Check:  in Section 4E”.

Is there DTC P P0500: Vehicle speed sensor (VSS) 
malfunction in ECM and/or DTC C1021, C1022, C1025, 
C1026, C1031, C1032, C1035 and/or C1036 in ABS/ESP

®

 

control module?

Go to applicable DTC 
diag. flow.

Go to Step 2.

2

Was “A/T System Check” performed?

Go to Step 3.

Go to “A/T System 
Check:  in related 
manual”.

3

Do you have SUZUKI scan tool?

Go to Step 4.

Go to Step 5.

4

4L switch and its circuit check

1) Connect SUZUKI scan tool to DLC with ignition switch 

OFF.

2) Turn ignition switch ON.

3) Select “DATA LIST” mode on scan tool.

4) Check 4L/N switch signal (ON or OFF) on display when 

turning transfer position switch to each position.

4L/N switch specifications
“4H” position: OFF
“4L” position: ON

Is OFF / ON displayed as described above?

Intermittent trouble or 
faulty TCM. Check for 
intermittent trouble 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00 in related manual”. If 
OK, substitute a known-
good TCM and recheck.

Go to Step 6.

5

4L/N switch and its circuit check

1) Turn ignition switch ON.

2) Check terminal voltage “E93-4” of TCM connector 

connected when turning transfer position switch to each 
position.

4L/N switch specifications
“4H” position: 10 – 14 V
“4L” position: 0 – 1 V

Is voltage as specified?

Intermittent trouble or 
faulty TCM. Check for 
intermittent trouble 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00 in related manual”. If 
OK, substitute a known-
good TCM and recheck.

Go to Step 6.

6

4L/N switch check

1) Check 4L/N switch for operation referring to “Transfer 

Assembly Inspection: Motor-Shift Type (Transfer with 
Shift Actuator) in Section 3C”.

Is check result satisfactory?

4L/N switch circuit open. 
If wire and connections 
are OK, substitute a 
known-good TCM and 
recheck.

Replace 4L/N switch.

Содержание GRAND VITARA JB416



























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRAND VITARA JB416

Hama Neptun Manual preview
Neptun
Бренд: Hama Страницы: 6
Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Бренд: Jeep Страницы: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Бренд: Jeep Страницы: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 525
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Бренд: RAM Commercial Страницы: 12
Conrad 75 16 30 Operating Instructions Manual preview
75 16 30
Бренд: Conrad Страницы: 26
Ford 2003 Thunderbird Owner'S Manual preview
2003 Thunderbird
Бренд: Ford Страницы: 200
Prorack K748 Fitting Instructions Manual preview
K748
Бренд: Prorack Страницы: 14
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Бренд: Safe Fleet Страницы: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Бренд: Honda Страницы: 4
Mitsubishi MIrage 2019 Owner'S Handbook Manual preview
MIrage 2019
Бренд: Mitsubishi Страницы: 19
Vangear Woody-Pod Instruction Manual preview
Woody-Pod
Бренд: Vangear Страницы: 5
Safe Fleet FRC SafeTrack Hardware Installation Manual preview
FRC SafeTrack
Бренд: Safe Fleet Страницы: 20
Pontiac 2007 G6 Owner'S Manual preview
2007 G6
Бренд: Pontiac Страницы: 486
Ford Mustang 2007 Supplement Manual preview
Mustang 2007
Бренд: Ford Страницы: 40
Saab 2000 9-5 2.3 Turbo Ecopower Owner'S Manual preview
2000 9-5 2.3 Turbo Ecopower
Бренд: Saab Страницы: 256
Saab 32 025 687 Installation Instructions Manual preview
32 025 687
Бренд: Saab Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды