manualshive.com logo in svg

Suzuki drz 400E, Руководство по обслуживанию, Страница: 94 / 334

Поделиться
Скачать
Suzuki drz 400E Скачать руководство пользователя страница 94

3-52

ENGINE

Apply a small quantity of THREAD LOCK “1342” or THREAD
LOCK SUPER “1322” to the pawl lifter screws, and then tighten
them securely.

For USA

99000-32050: THREAD  LOCK “1342”

For the other countries

99000-32110: THREAD LOCK SUPER “1322”

PRIMARY DRIVE GEAR

Install the key 

1

 and primary drive gear 

2

.

Hold the generator rotor using the special tool (DR-Z400) or
a 26-mm offset wrench (DR-Z400E), and then tighten the
primary drive gear nut to the specified torque.

09930-44913: Rotor holder

Primary drive gear nut: 110 N·m (11.0 kgf-m, 79.5 lb-ft)

GEARSHIFT CAM DRIVEN GEAR

Tighten the gearshift cam driven gear bolt to the specified
torque.

Gearshift cam driven gear bolt:

24 N·m (2.4 kgf-m, 17.5 lb-ft)

Install each pawl lifter into the gearshift cam driven gear. The
large shoulder 

A

 must face to the outside.

1

2

Содержание drz 400E















































































































































































































































































































































Отзывы:

Нет отзывов