Suzuki drz 400E Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 334

background image

CHASSIS

6-37

Move the rod and drain the oil completely into a drain pan.
Push the valve core again to equalize atmospheric pressure.

Fill a drain pan with the specified rear suspension oil.
Place the rear shock absorber into the drain pan so that the
drain hole is submerged in the oil, and then fill the rear shock
absorber with the oil by stroking the rod.

99000-99001-S25:

SUZUKI REAR SUSPENSION OIL SS-25

Oil capacity:

Approximately 380 ml (12.8 US oz, 13.4 lmp oz)

When fitting the orifice in the compression adjuster hole, face
the conical side to the valve side.
Tighten the compression adjuster assembly to the specified
torque.

Replace the remove O-rings with new ones.

Compression adjuster assembly:

30 N·m (3.0 kgf-m, 21.5 lb-ft)

Fill the rear shock absorber unit with nitrogen gas.

Rear shock absorber gas pressure:

900 kPa (9.0 kgf/cm

2

, 128 psi)

Tighten the gas valve cap.

Use of flammable gas for pressuring the rear shock
absorber unit can be hazardous. Flammable gas such
as gas welding oxygen can create a fire hazard.
Use nitrogen gas. If nitrogen gas is not available,
compressed air free from water can be substituted.
Applying too much pressure to the rear shock ab-
sorber unit may rupture the rear shock absorber unit.
Be sure to fill the rear shock absorber unit to the
specified pressured.

«
...
166
167
168
169
170
...
»

Содержание drz 400E















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для drz 400E

Бренд: LAZER Страницы: 6

Бренд: Dennis Kirk Страницы: 5

Бренд: Suzuki Страницы: 199

Бренд: FDC Страницы: 6

Rebellion Electric Chopper 15130760

Бренд: Razor Страницы: 17

Minirack 6602533 01 01

Бренд: hepco & becker Страницы: 4

Бренд: Pandora Страницы: 56

Бренд: N-Com Страницы: 32

MOTO NOSTRA MN4602

Бренд: SC Страницы: 8

Бренд: DYNATEK Страницы: 5

Бренд: DYNATEK Страницы: 8

Бренд: hepco & becker Страницы: 4

Бренд: Chicago Electric Страницы: 12

X-FORCE PRO 50 2017

Бренд: Kuberg Страницы: 28

Бренд: Dräger Страницы: 256

Бренд: Healtech Страницы: 2

Бренд: Healtech Страницы: 3

Бренд: KED Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды