Suzuki drz 400E Скачать руководство пользователя страница 201

Страница: 201 / 334

7-8

ELECTRICAL SYSTEM

TROUBLESHOOTING

• Remove accessories

Accessories
are installed

Check accessories which use excessive
amounts of electricity.

Battery runs down quickly.

Others

No accessories

• Short circuit of the wire
harness
• Loose or disconnected
wires
• Faulty battery

Current leaks

Correct

No continuity

Incorrect

Check the battery for current leak-
age.

No current leaks

• Faulty battery
• Abnormal driving
condition

Measure the regulated voltage.

Incorrect

• Faulty stator coil or
disconnected lead
wires

Check the continuity of the
generator.

Continuity

• Faulty generator

Inspect the generator no-load
performance.

Correct

• Faulty rectifier or
regulator/rectifier

Inspect the regulator/rectifier.

Correct

• Short circuit of wire
harness
• Improper coupler
contact

• Faulty battery

Inspect the wires.

Battery overcharges

Correct

( 7-9)

( 7-9 and 7-10)

( 7-10)

( 7-11)

• Faulty rectifier or regulator/rectifier
• Faulty battery
• Poor contact of generator lead wire coupler

Содержание drz 400E















































































































































































































































































































































Результаты поиска

Содержание drz 400E

Отзывы:

Похожие инструкции для drz 400E

Бренды по названию

Популярные бренды

Suzuki drz 400E, Руководство по обслуживанию

Результаты поиска

Содержание drz 400E

Отзывы:

Похожие инструкции для drz 400E

Бренды по названию

Популярные бренды