manualshive.com logo in svg

Suzuki drz 400E, Руководство по обслуживанию, Страница: 208 / 334

Поделиться
Скачать
Suzuki drz 400E Скачать руководство пользователя страница 208

ELECTRICAL SYSTEM

7-15

OIL SEAL

Check the seal lip for damage or leakage. If any damages are
found, replace the housing end (inside) of the starter motor with
a new one.

STARTER MOTOR REASSEMBLY AND
REMOUNTING

Reassemble and remount the starter motor in the reverse order
of removal and disassembly. Pay special attention to the follow-
ing points:

Replace the removed O-rings with new ones to pre-
vent oil leakage and moisture.

Apply SUZUKI SUPER GREASE “A” to the lip of the oil seal.

For USA

99000-25030: SUZUKI SUPER GREASE “A”

For the other countries

99000-25010: SUZUKI SUPER GREASE “A”

Apply a small quantity of SUZUKI MOLY PASTE to the arma-
ture shaft.

99000-25140: SUZUKI MOLY PASTE

Align the match marks on the starter motor case with the match
mark on the housing end.
Apply a small quantity of THREAD LOCK “1342” to the starter
motor housing bolts.

99000-32050: THREAD  LOCK “1342”

Apply SUZUKI SUPER GREASE “A” to the O-ring.

For USA

99000-25030: SUZUKI SUPER GREASE “A”

For the other countries

99000-25010: SUZUKI SUPER GREASE “A”

Содержание drz 400E















































































































































































































































































































































Отзывы:

Нет отзывов