Suzuki drz 400E Скачать руководство пользователя страница 329

Страница: 329 / 334

11-26

DR-Z400/EK2 (’02-MODEL)

• Apply THREAD LOCK SUPER “1303” to the seat rail lower

mounting bolt

99000-32030: THREAD LOCK SUPER “1303”

• Tighten the seat rail upper mounting nut

and lower mount-

ing bolts

to the specified torque.

Seat rail upper mounting nut:

35 N·m (3.5 kgf-m, 25.5 lb-ft)

Seat rail lower mounting bolt:

35 N·m (3.5 kgf-m, 25.5 lb-ft)

DAMPING FORCE ADJUSTMENT

After installing the rear suspension, adjust the rebound and com-
pression damping force as follows.

NOTE:
Do not turn the adjust screws more than the given position or the
adjuster may be damaged.

REBOUND DAMPING FORCE ADJUSTMENT

Fully turn the damping force adjuster

clockwise. It is at stiffest

position and turn it out to standard position.

Standard setting position: 13 clicks out

COMPRESSION DAMPING FORCE ADJUSTMENT

Compression damping force could be adjusted in two stage by
turning the two adjusters.

High speed damping force

Fully turn the high speed damping force adjuster

clockwise. It

is at stiffest position and turn it out to standard position.

Low speed damping force

Fully turn the low speed damping force adjuster

clockwise. It

is at stiffest position and turn it out to standard position.

Standard setting position
High speed damping: 1

turn out

Low speed damping: 10 clicks out

Содержание drz 400E















































































































































































































































































































































Результаты поиска

Содержание drz 400E

Отзывы:

Похожие инструкции для drz 400E

Бренды по названию

Популярные бренды

Suzuki drz 400E, Руководство по обслуживанию

Результаты поиска

Содержание drz 400E

Отзывы:

Похожие инструкции для drz 400E

Бренды по названию

Популярные бренды