Suzuki drz 400E Скачать руководство пользователя страница 308

Страница: 308 / 334

DR-Z400/EK2 (’02-MODEL)

11-5

CHASSIS

Front suspension ...................................................

Telescopic, coil spring, oil damped

Rear suspension ....................................................

Link type, coil spring, oil damped

Front fork stroke .....................................................

288 mm (11.3 in)

Rear wheel travel ...................................................

295 mm (11.6 in)

Caster ....................................................................

27° 20’

Trail .........................................................................

112 mm (4.41 in)

Steering angle .......................................................

45° (right & left)

Turning radius ........................................................

2.2 m (7.2 ft)

Front brake .............................................................

Disc brake

Rear brake .............................................................

Disc brake

Front tire size .........................................................

80/100-21 51P or 80/100-21 M/C 51P

Rear tire size ..........................................................

120/90-18 65P or 120/90-18 M/C 65P

ELECTRICAL

Ignition type ...........................................................

Electronic ignition (CDI)

Ignition timing .........................................................

7° BTDC at 1 800 r/min

Spark plug ..............................................................

NGK: CR8E
DENSO: U24ESR-N

Generator ...............................................................

Three-phase A.C. generator

Battery ...................................................................

12 V 21.6 kC (6 Ah)/10 HR

Fuse .......................................................................

20 A

Headlight ................................................................

12 V 60/55 W

Brake light/Taillight .................................................

12 V 21/5 W

Turn signal light ......................................................

12 V 21 W

Speedometer light ..................................................

LED

Neutral indicator light .............................................

12 V 2 W

High beam indicator light .......................................

12 V 2 W

Turn signal indicator light .......................................

12 V 2 W

CAPACITIES

Fuel tank, including reserve ..................................

10.0 L (2.6 US gal, 2.2 Imp gal)

reserve ..................................................

2.3 L (0.6 US gal, 0.5 Imp gal)

Engine oil, oil change ............................................

1 700 ml (1.8 US qt, 1.5 Imp qt)

oil and filter change .............................

1 800 ml (1.9 US qt, 1.6 Imp qt)

engine overhaul ...................................

1 900 ml (2.0 US qt, 1.7 Imp qt)

Front fork oil ...........................................................

720 ml (24.3 US oz, 25.4 Imp oz)

Engine coolant .......................................................

1 250 ml (1.3 US qt, 1.1 Imp qt)

NOTE:
These specifications are subject to change without notice.

Содержание drz 400E















































































































































































































































































































































Результаты поиска

Содержание drz 400E

Отзывы:

Похожие инструкции для drz 400E

Бренды по названию

Популярные бренды

Suzuki drz 400E, Руководство по обслуживанию

Результаты поиска

Содержание drz 400E

Отзывы:

Похожие инструкции для drz 400E

Бренды по названию

Популярные бренды