manualshive.com logo in svg

Suzuki drz 400E, Руководство по обслуживанию, Страница: 66 / 334

Поделиться
Скачать
Suzuki drz 400E Скачать руководство пользователя страница 66

3-24

ENGINE

VALVE HEAD RADIAL RUNOUT

Support the valve using a V-block and measure the valve head
radial runout using the dial gauge, as shown. If the runout ex-
ceeds the service limit, replace the valve with a new one.

09900-20606: Dial gauge (1/100 mm)
09900-20701: Magnetic stand
09900-21304: V-block set (100 mm)

Valve head radial runout
Service Limit: 0.03 mm (0.001 in)

VALVE FACE WEAR

Visually inspect each valve face for wear or damage. If any ab-
normal wear is found, replace the respective valve with a new
one. Measure the valve face thickness 

T

. If the valve face thick-

ness is not within the specified value, replace the valve with a
new one.

09900-20101: Vernier  calipers

Valve face thickness 

T

T

T

T

T

Service Limit: 0.5 mm (0.02 in)

VALVE STEM DEFLECTION

Lift the valve about 10 mm (0.39 in) from the valve seat. Mea-
sure the valve stem deflection in two directions, “X” and “Y”, per-
pendicular to each other. Position the dial gauge as shown. If the
deflection exceeds the service limit, determine whether the valve
or the guide should be replaced with a new one.

09900-20606: Dial gauge (1/100 mm)
09900-20701: Magnetic stand

Valve stem deflection
Service Limit: 0.35 mm (0.014 in)

VALVE STEM WEAR

Measure the valve stem outside diameter using the micrometer.
If the outside diameter is not within the specified value, replace
the valve with a new one. If the valve stem outside diameter is
within specification, but the valve stem deflection is not, replace
the valve guide with a new one. After replacing the valve or valve
guide, check the deflection.

09900-20205: Micrometer (0 – 25 mm)

Valve stem O.D.
Standard:
IN: 4.975 – 4.990 mm (0.1959 – 0.1965 in)
EX: 4.955 – 4.970 mm (0.1951 – 0.1957 in)

X

Y

Содержание drz 400E















































































































































































































































































































































Отзывы:

Нет отзывов