Suzuki drz 400E Скачать руководство пользователя страница 229 | Manualshive

Страница: 229 / 334

background image

SERVICING INFORMATION

8-5

Complaint

Symptom and possible causes

Remedy

Engine overheats.

1. Carbon buildup on piston crown.
2. Insufficient amount of engine oil.
3. Defective oil pump.
4. Clogged oil circuit.
5. Float chamber fuel level too low.
6. Air leakage from intake pipe.
7. Incorrect engine oil.

Clean.
Check level and add.
Replace.
Clean.
Adjust float height.
Tighten or replace.
Change.

CARBURETOR

Starting difficulty.

1. Clogged starter jet.
2. Clogged starter jet passage.
3. Air leaking from joint between starter body and carbu-

retor.

4. Air leaking from carburetor joint or vacuum hose joint.

5. Improperly working starter (enricher) plunger.

Clean.
Clean.
Tighten, adjust, or replace
gasket.
Tighten or replace defective
part.
Adjust.

Idling or low-speed
trouble.

1. Clogged or loose pilot jet.
2. Clogged or loose pilot air jet.
3. Air leaking from carburetor joint, vacuum pipe joint, or

starter.

4. Clogged pilot outlet port.
5. Clogged bypass port.
6. Starter (enricher) plunger not fully closed.

Clean or tighten.
Clean or tighten.
Tighten or replace defective
part.
Clean.
Clean.
Adjust.

Medium or high-
speed trouble.

1. Clogged main jet.
2. Clogged main air jet.
3. Clogged needle jet.
4. Improperly working throttle valve.
5. Clogged fuel filter.

Clean.
Clean.
Clean.
Adjust.
Clean or replace.

Overflow and fuel
level fluctuations.

1. Worn or damaged needle valve.
2. Broken needle valve spring.
3. Improperly working float.
4. Foreign matter on the needle valve.

5. Incorrect float chamber fuel level.

Replace.
Replace.
Adjust or replace.
Clean or replace with needle
valve seat.
Adjust float height.

Complaint

Symptom and possible causes

Remedy

«
...
227
228
229
230
231
...
»

Содержание drz 400E















































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для drz 400E

Бренд: KEDO Страницы: 2

Бренд: KEDO Страницы: 3

Бренд: KEDO Страницы: 2

Бренд: Yamaha Страницы: 572

Бренд: Yamaha Страницы: 584

Бренд: Yamaha Страницы: 410

Бренд: Yamaha Страницы: 576

Бренд: Yamaha Страницы: 668

Бренд: Yamaha Страницы: 596

Бренд: Yamaha Страницы: 656

Бренд: Yamaha Страницы: 378

Бренд: LAMAX Страницы: 134

Бренд: GLOBBER Страницы: 72

Бренд: R&G Страницы: 8

Бренд: Würth Страницы: 188

Бренд: N-Com Страницы: 2

Бренд: R&G Страницы: 24

Бренд: Suzuki Страницы: 440

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды