manualshive.com logo in svg

Suzuki drz 400E, Руководство по обслуживанию, Страница: 272 / 334

Поделиться
Скачать
Suzuki drz 400E Скачать руководство пользователя страница 272

DR-Z400EY (E-24 MODEL)

9-15

With each press of the MODE TIME button, the display changes
between the clock, the stopwatch and the timer as shown below.

Clock

Stopwatch

Timer

TRIP TIME

MODE

     

TIME

CLOCK

TIME

CLOCK

TIME

CLOCK

"

To avoid riding with only one hand, do not operate the
buttons while riding.

NOTE:

Make sure not to press more than one button at a time.
Before performing the operations described in this section,
be sure to start the engine in order to prevent the battery from
being drained.

ODOMETER

Displays the total distance travelled

TRIP TIME

MODE

   

     

TOTAL

TRIPMETER

Displays the distance travelled since the tripmeter was last
reset.

NOTE:
The tripmeters A and B can be used independently.

TRIP TIME

MODE

   

     

TRIP

TRIP

A

B

Switching between addition and subtraction modes

TRIP

TIME/

TRIP

SET

   

     

TRIP

TRIP

A

B

     

                                                

+

–

ADJUST

Press the SET TRIP button to reset the tripmeter.

TRIP

TIME/

TRIP

SET

Displays the distance with a calibration coefficient (70 – 130 %) applied

                                                     

TRIP

TIME/

TRIP

SET

   

     

TRIP

TRIP

A

B

   

                                        

+

–

ADJUST

   

                                        

TRIP

TIME/

TRIP

SET

S u b t r a c t i o n
mode 

No sign indicates

addition mode.

Make addition or subtrac-
tion calculations.

Select the calibration
coefficient.

Hold down the SET TIME/TRIP
button for three seconds.

Return to the normal
display.

Содержание drz 400E















































































































































































































































































































































Отзывы:

Нет отзывов