manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 71

71

13. Reinstall the fuel filter with bracket by secur-

ing the bolt and nut.

14. Restart the engine and check that there are

no leaks around the fuel filter.

NOTE:
If any water exists in the fuel filter cup, remove
the cup and drain the water. Always dispose of
excess fuel safely. For questions, consult your
authorized Suzuki marine dealer.

LUBRICATION

Proper lubrication is important for the safe,
smooth operation and long life of each working
part of your outboard motor. The following chart
shows the lubrication points of your motor and
the recommended lubricant:

LOCATION

LUBRICANT

Throttle/Shift linkage

Marine-grade 
water resistant 
grease

Propeller shaft

Trim ram pad

(DF140A & DF115AS)

NOTE:
Before applying grease through the steering
bracket grease nipple, lock the motor in the fully
tilted up position.

Your authorized Suzuki Marine Dealer may also
have additional recommendations due to
regional climate or operating conditions.
Please consult him for advice.

Marine-grade 
water resistant 
grease
(Grease Gun)

Swivel bracket

DF115A

transom “L”

Steering bracket

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды