manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 23

23

If you change propellers, be sure to perform the
above check again, to confirm that the engine
speed under full throttle is within the specified
range.

PROPELLER INSTALLATION

To install a propeller on your outboard motor,
use the following procedure:

1. Coat the propeller shaft splines 

1

 liberally

with Suzuki water resistant grease to help
prevent corrosion.

2. Place the stopper 

2

 on the shaft.

3. Align the propeller 

3

 with the propeller shaft

splines and slide the propeller onto the shaft.

4. Place the spacer 

4

 and washer 

5

 on the

shaft.

5. Install the propeller nut 

6

 and tighten it with

a torque wrench to 50 – 60 N·m (5.1 – 6.1
kgf-m/37 – 44 lbf-ft).

 WARNING

Failure to take proper precautions when
installing or removing the propeller can
result in severe personal injury.

When installing or removing the propeller:
• Always shift into “Neutral” and remove

the emergency stop switch lock plate
so that the motor cannot be started
accidentally.

• Wear gloves to protect hands, and

“lock” the propeller by placing a block
of wood between the blades and the
anti-cavitation plate.

6. Align the grooves in the propeller nut with

the hole in the shaft, then insert the cotter
pin 

7

 and bend the pin ends over to lock it in

place.

To remove the propeller, reverse the above pro-
cedure.

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды