manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 60

60

Horizontal transport:

1. Drain the engine oil. Refer to the ENGINE

OIL section.

2. Drain the gasoline from the vapor separator

as follows:

(1) Remove the motor cover 

1

.

(2) Remove the seven (7) bolts using a 8 mm

box wrench, then remove the starboard side
cover 

2

.

(3) Pull the drain hose end 

3

 out.

(4) Loosen the vapor separator drain screw 

4

and drain the gasoline into a suitable con-
tainer.

(5) After draining, retighten the drain screw and

reinstall the all items back in place.

3. Rest the motor on a case protector with the

starboard side downwards as shown.

 WARNING

Gasoline is extremely flammable and
toxic.  It can cause a fire and can be haz-
ardous to people and pets.

Use a proper, safe container to store any
gasoline drained from the outboard
motor.  Keep gasoline away from sparks,
flames, people, and pets.

NOTICE

If spilled gasoline is just left on painted
surface, it may cause a stain or discolora-
tion of the surface coating.

Wipe off any spilled gasoline immediately
with a soft cloth etc.

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды