manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 13

13

BATTERY INSTALLATION

BATTERY REQUIREMENT

650 Marine Cranking Amps (MCA)/ABYC,
or 512 Cold Cranking Amps (CCA)/SAE
or 160 Reserve Capacity (RC) Minutes/SAE

NOTE:
• The specifications listed above are the mini-

mum battery rating requirements for starting
the engine. 

• Additional electrical loads from the boat will

require larger capacity batteries. Consult
your Suzuki dealer to determine the proper
battery sizing for your boat and engine com-
bination.

• Dual-purpose (Cranking/Deep-cycle) batter-

ies can be used if they meet the minimum
specifications listed above (MCA, CCA, or
RC).

• Do not use a Deep Cycle battery for the main

cranking battery.

• When connecting batteries in parallel, they

must be of the same type, capacity, manufac-
turer, and of similar age. When replacement
is necessary, they should be replaced as a
set.  Consult your Suzuki dealer for proper
battery installation information.

BATTERY INSTALLATION

Secure the battery in a dry area of the boat,
away from vibration.

NOTE:
• It is recommended that the battery be

installed in an enclosed battery case.

• When connecting batteries, hexagon-nuts

must be used to secure battery leads to bat-
tery posts.

To hook up the battery, first connect the red
lead from the motor to the positive battery ter-
minal, then connect the black lead to the nega-
tive battery terminal.

 WARNING

If you place the battery near the fuel tank,
a spark from the battery may ignite the
gasoline, causing a fire and/or an explo-
sion.

Do not place the fuel tank in the same
compartment/area as the battery.

Red lead

Sub battery cable

Black 
lead

White lead

Hexagon-nut

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды