manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 46

46

NOTE:
There is a spare plastic lock plate for temporary
use only. Remove it from the cord and place in
a safe place on the boat. However, the original
cord and lock plate should be replaced as soon
as possible.

STARTING THE ENGINE

NOTE:
If the emergency stop switch lock plate is not in
position, the starter motor cannot operate.

 WARNING

Failure to properly attach the emergency
stop switch cord or to take proper pre-
cautions to help ensure that the emer-
gency stop switch works as intended may
result in serious injury or death to the
operator or passengers.

Always take the following precautions:
• Make sure that the emergency stop

switch cord is fastened securely to the
operator’s wrist or to an appropriate
clothing area (belt etc.).

• Ensure that no obstructions impede or

restrict emergency stop switch opera-
tion.

• Be careful not to pull the stop switch

cord or knock out the lock plate during
normal operation. The motor will stop
abruptly, and the loss of forward
motion may unexpectedly throw occu-
pants forward. 

 WARNING

Exhaust gas contains carbon monoxide,
a dangerous gas that is difficult to detect
because it is colorless and odorless.
Breathing carbon monoxide can cause
death or severe injury.

Never start the engine or let it run indoors
or where there is little or no ventilation. 

If equipped with Keyless Start System:
1. Squeeze the fuel line priming bulb several

times until you feel resistance.

2. Side mount type:

Make sure that the warm-up lever is in the
fully closed position.

3. (1) Confirm that the key-fob is in communi-

cation ON mode (Refer to the “Switching
the Communication mode of the key-fob”
section.)

(2) While the key-fob is within the communi-

cation range of the keyless control unit,
turn the main switch to the “ON & OFF”
(“

”) position and then release it. The

main switch automatically returns to the
“PUSH START/STOP” position.  
The buzzer sounds twice to notify that
the Keyless Start System has been
turned ON.

NOTE:
If equipped with Dual Engine:
When either one of the engines of Keyless Start
System is turned ON, another engine will auto-
matically be turned ON. 

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды