manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 59

59

Cancelling the troll mode:

The troll mode can be cancelled by shifting the
remote control lever to the neutral position, or
by increasing the engine speed to 3000 r/min or
more. In both cases, two short beeps sound
when cancelling the troll mode.

OPERATION IN SALT WATER

After operating the motor in salt water, you
should flush the water passages with clean,
fresh water as outlined in the FLUSHING THE
WATER PASSAGES section. If you do not flush
the water passages, salt can corrode the motor
and shorten its life.

OPERATION IN FREEZING WEATHER

When operating your outboard motor in freez-
ing temperatures, you should keep the lower
unit submerged in the water at all times.
When taking motor out of the water, stand it up
in a vertical position until the cooling system
drains completely.

NOTICE

If you leave your outboard motor out of
the water in freezing temperatures with
water still in the cooling system, the
water can freeze and expand, causing
severe damage to the motor.

When your outboard is in the water in
freezing temperatures, keep the lower
unit submerged in the water at all times.
When the motor is stored out of the water
in freezing temperatures stand it up in the
vertical position so that the cooling sys-
tem drains completely.

MOTOR REMOVAL AND 
TRANSPORTING

MOTOR REMOVAL

If it is necessary to remove the outboard motor
from your boat, we recommend that you ask
your authorized Suzuki Marine Dealer to do the
work for you.

MOTOR TRANSPORTING

When transporting the motor, place the motor
either vertically or horizontally.

Vertical transport:

Attach the motor to the carrier by securing
clamp bracket with two sets of transom bolt and
nut.
Never use display stand for transportation of the
motor.

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды