manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 41

41

INSPECTION BEFORE 
BOATING

It is important to make sure that your boat and
motor are in good condition and that you are
properly prepared for an emergency.
Always perform the following checks before you
begin boating:

• Check that you have enough fuel for the

intended run.

• Check the level of engine oil in the sump.

To check the oil level:

NOTE:
To avoid an incorrect assessment of engine oil
level, check the level only when the engine has
cooled.

 WARNING

Failure to inspect your boat and motor
before beginning a trip can be hazardous.

Before boating, always perform the
inspections described in this section.

NOTICE

Running the engine with an insufficient
amount of oil can cause serious engine
damage.

Always check the oil level before each
trip and add oil if necessary.

1. Place the motor in a vertical position, then

remove the motor cover 

1

 by unlocking the

lever 

2

 and 

3

.

2. Pull out the oil dipstick and wipe oil off with a

clean cloth.

NOTE:
If the engine oil is contaminated or discolored,
replace with fresh engine oil. Refer to the
ENGINE OIL section.

3. Insert the dipstick all the way into the engine,

then remove it again.

UPPER LIMIT

LOWER LIMIT

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды