manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 22

22

(2) The LED on the key-fob blinks once and the

buzzer sounds once. 
After that, the LED on the key-fob blinks to
indicate the passcode by the number of
blinks, as shown in the illustration. 
This is indicated repeatedly.

NOTE:
The passcode indication will not start if Step (1)
is not performed within eight (8) seconds or the
operation fails.
In this case, turn the main switch to the “ON &
OFF” 

(“

”) 

position and then release it to the

“PUSH START/STOP” position to turn the Key-
less Start System OFF. After that, retry the pro-
cedure from Step 5.

7. After the passcode confirmation is com-

pleted, turn the main switch to the “ON &
OFF” (“

”) position and then release it. The

main switch automatically returns to the
“PUSH START/STOP” position. The Keyless
Start System turns OFF and the passcode
indication stops.  

Example: In the case of passcode 1234

LED

PROPELLER SELECTION 
AND INSTALLATION

PROPELLER SELECTION

It is essential to use a propeller on your out-
board motor that is properly matched to your
boat’s operating characteristics. The speed of
the engine when you operate your boat at full
throttle depends on the propeller you use.
Excessive engine speed can seriously damage
the motor, while low engine speed at full throttle
will adversely affect the performance. Your
operating load will also affect propeller selec-
tion. Smaller loads generally require larger-
pitch propellers; larger loads generally require
smaller-pitch propellers. Your authorized Suzuki
Marine Dealer will assist you in selecting a suit-
able propeller for your boat.

You can determine if your propeller is appropri-
ate for use with your boat by using a tachome-
ter to measure engine speed when operating
your boat at full throttle, under minimum load
conditions. If you are using an appropriate pro-
peller, the engine speed will be within the fol-
lowing range:

If the engine speed is not within this range, con-
sult your authorized Suzuki Marine Dealer to
determine which propeller size is best for you.

NOTICE

Installing a propeller with either too much
or too little pitch will cause incorrect
maximum engine speed, which may
result in severe damage to the motor.

Ask your authorized Suzuki marine
dealer to assist you in selecting a suit-
able propeller for your boat.

DF115A/115AS

5000 – 6000
r/min. (min

–1

)

DF140A

5600 – 6200
r/min. (min

–1

)

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды