manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 53

53

NOTE:
Starting of another engine of the Dual Engine:
Push the main switch to start the engine.

To stop the engine:

1. Shift into “NEUTRAL”.
2. After operating at full throttle, cool off the

engine a few minutes by allowing it to idle or
troll at low speed.

3. Push the emergency key to stop the engine.

NOTE:
Stopping of another engine of the Dual Engine:
Push the main switch to stop the engine.

ON & OFF

PUSH
START

STOP

* If equipped with top mount type 
  remote control box: (Main switch panel) 
  “ON & OFF”        “     ” 

4. Turn the emergency key to the “ON & OFF”

(“

”) position and then release it to the

“PUSH START/STOP” position to turn the
Keyless Start System to OFF state. And
then, pull out the emergency key from the
key cylinder. 

NOTE:
The passcode authentication state is main-
tained for 15 seconds after turning the emer-
gency key to the “PUSH START/STOP”
position. In this state, the engine can be started
by turning the emergency key to the left and
pressing the main switch. To restart the engine
when the 15-second period has elapsed after
turning the emergency key to the “PUSH
START/STOP” position, repeat the emergency
key operation from the beginning. 

ON & OFF

ON & OFF

PUSH
START
STOP

PUSH
START
STOP

* If equipped with top mount type 
  remote control box: (Main switch panel) 
  “ON & OFF”        “     ” 

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды