manualshive.com logo in svg

Suzuki DF115A, Руководство пользователя

Поделиться
Скачать
Suzuki DF115A Скачать руководство пользователя страница 19

19

SETTING AND/OR CHANGING THE PASS-
CODE

By setting a 4-digit passcode, the engine can
be started by entering the passcode even if the
key-fob battery has run down or the key-fob is
lost.
The same method is used to set and change
the passcode.

NOTE:
Carry the passcode with the emergency key in
case the key-fob battery runs down or the key-
fob is lost. 

NOTE:
When the passcode has been updated or
changed, the previous passcode is deleted and
updated to the new passcode.

Use the following procedure to set or change
the passcode: 
1. Confirm the engine is stopped. 
2. Make sure the emergency switch lock plate

is in place.

3. Confirm the key-fob is within the communi-

cation range of the Keyless Start System. 

4. Confirm that the key-fob is in communication

ON mode. (Refer to “Switching the commu-
nication mode of the key-fob” section.)

5. Turn the main switch to the “ON & OFF”

(“

”) position and then release it. The main

switch automatically returns to the “PUSH
START/STOP” position. 
The buzzer on the engine control side emits
one (1) long sound while the buzzer on the
keyless control unit side emits two (2) short
sounds simultaneously. 

ON & OFF

ON & OFF

PUSH
START

STOP

PUSH
START

STOP

If equipped with side mount type 
remote control box:

6. Pull out the emergency stop switch lock

plate.

7. Within eight (8) seconds after performing

Step 5, start the following operation. 

(1) Turn the main switch to the “ON & OFF”

(“

”) position and hold it for about five (5)

seconds then release it to the “PUSH
START/STOP” position. 
Repeat this operation for two more times.
The buzzer sounds once and the system
enters stand-by mode for passcode input.

NOTE:
The buzzer will not sound if the operation in
Step (1) is not performed within eight (8) sec-
onds or the operation fails. 

PUSH
START

STOP

PUSH
START

STOP

If equipped with top mount type 
remote control box: (Main switch panel)

Содержание DF115A




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды