Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 87

Страница: 87 / 96

Chapter 7: BIOS

7-15

7-4 Boot

Menu

The Boot Menu is accessible only when the "Load Onboard LAN Option ROM"

setting (in the PCI/PnP Confi guration menu) is enabled.

Boot Device Priority

This feature allows you to prioritize the boot sequence from the list of available

devices. A device that is in parenthesis has been disabled in the corresponding

type menu.

Hard Disk Drives

This feature allows you to specify the boot sequence from the list of available hard

disk drives. A device that is in parenthesis has been disabled in the corresponding

type menu.

CD/DVD Drives

This feature allows you to specify the boot sequence from the list of available CD/

DVD drives. A device that is in parenthesis has been disabled in the corresponding

type menu.

Retry Boot Devices

This option allows you to retry boot devices. Options include Enabled and

Disabled

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды