Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 48

Страница: 48 / 96

5-14

UPER

ERVER 1012G-MTF User's Manual

5-9 Connector

Defi nitions

Power Connectors

A 24-pin main power supply connector(JPW1)

and three 8-pin CPU PWR connector (JPW2)

on the motherboard. These power connectors

meet the SSI EPS 12V specification. In

addition to the 24-pin ATX power connector,

the 12V 8-pin CPU PWR connector at JPW2

must also be connected to your power

supply. See the table on the right for pin

defi nitions.

Warning

: To prevent damage to the power

supply or motherboard, please use a power

supply that contains both a 24-pin and 8-pin

power connectors. Be sure to connect these

connectors to the 24-pin (JPW1) and the

three 8-pin (JPW2) power connectors on the

motherboard. Failure in doing so will void the

manufacturer warranty on your power supply

and motherboard.

Reset Connector

The reset connector is located on pins 3 and

4 of JF1 and attaches to the reset switch on

the computer chassis. See the table on the

right for pin defi nitions.

PW_ON Connector

The PW_ON connector is on pins 1 and 2 of

JF1. This header should be connected to the

chassis power button. See the table on the

right for pin defi nitions.

Overheat/Fan Fail LED (OH)

Connect an LED to the OH connection on

pins 7 and 8 of JF1 to provide advanced

warning of chassis overheating or fan

failure. Refer to the table on the right for pin

defi nitions and status indicators.

ATX Power 24-pin Connector

Pin Defi nitions

Pin# Defi nition Pin # Defi nition

+3.3V

-12V

+3.3V

COM

PS_ON

+5V

COM

+5V

COM

Res (NC)

PWR_OK

+5V

5VSB

+5V

+12V

+5V

+12V

COM

+3.3V

Required Connection

Reset Button

Pin Defi nitions

(JF1)

Pin# Defi nition

Reset

Ground

Power Button

Pin Defi nitions

(JF1)

Pin# Defi nition

PW_ON

Ground

OH/Fan Fail LED

Pin Defi nitions

(JF1)

Pin# Defi nition

Vcc

Control

OH/Fan Fail

LED Status

State Indication

Solid

Overheat

Blinking

Fan fail

12V 8-pin PWR Connector

Pin Defi nitions

Pins Defi nition

1 through 4

Ground

5 through 8

+12V

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды