Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 27

Страница: 27 / 96

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the SAS/SATA

drive carriers to keep you constantly informed of the overall status of the system as

well as the activity and health of specifi c components. There are also two buttons

on the chassis control panel and an on/off switch on the power supply. This chapter

explains the meanings of all LED indicators and the appropriate response you may

need to take.

3-2 Control Panel Buttons

There are two push-buttons located on the front of the chassis: a reset button and

a power on/off button.

Reset

The reset button reboots the system.

Power

This is the main power button, which is used to apply or turn off the main system

power. Turning off system power with this button removes the main power but keeps

standby power supplied to the system.

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды