Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 81

Страница: 81 / 96

Chapter 7: BIOS

7-9

PCI/PnP Confi guration

Clear NVRAM

Select Yes to clear NVRAM during boot-up. The options are Yes and

Plug & Play O/S

Select Yes to allow the OS to confi gure Plug & Play devices. (This is not required

for system boot if your system has an OS that supports Plug & Play.) Select

to allow AMIBIOS to confi gure all devices in the system.

PCI Latency Timer

This option sets the latency of all PCI devices on the PCI bus. Select a value

to set the PCI latency in PCI clock cycles. Options are 32,

, 96, 128, 160,

192, 224 and 248.

PCI IDE Busmaster

Use this setting to

Enable

or Disable BIOS enabled uses of PCI Busmastering

for reading or writing to IDE drives.

ROM Scan Ordering

This setting determines which kind of option ROM activates prior to another.

Options include

Onboard First

and Addon First.

PCI Slot 1/PCI Slot 2/PCI Slot 3

These settings

Enable

or Disable the specifi ed PCI slot in your system.

PCIE x4 Slot4/PCI x8 Slot 5/PCI x8/x16 Slot 6

These settings

Enable

or Disable the specifi ed PCIE slot in your system.

Onboard LAN Option ROM Select

This setting allows you to select the onboard LAN option ROM for iSCSI or

PXE

Note

: You must enable

ONLY

LAN1 when the iSCSI support option is

specifi ed.

Load Onboard LAN 1 Option ROM

This option allows you to

enable

or disable the onboard LAN 1 option ROM.

Load Onboard LAN 2 Option ROM

This option allows you to

enable

or disable the onboard LAN 2 option ROM.

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды