Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 52

Страница: 52 / 96

5-18

UPER

ERVER 1012G-MTF User's Manual

ATX PS/2 Keyboard and PS/2 Mouse

Ports

The ATX PS/2 keyboard and PS/2 mouse are

located next to the Back Panel USB Ports

0~3 on the motherboard. See the table at

right for pin defi nitions.

PS/2 Keyboard/Mouse Pin

Defi nitions

PS2 Keyboard

PS2 Mouse

Pin# Defi nition

KB Data

Mouse Data

No
Connection

Ground

Mouse/KB
VCC (+5V)

KB Clock

Mouse Clock

No
Connection

VCC: with 1.5A PTC (current limit)

Power LED/Speaker

On the JD1 header, pins 1~3 are used for

power LED indication, and pins 4-7 are for

the speaker. See the tables on the right for

pin defi nitions. If you wish to use the onboard

speaker, you should close pins 6~7 with a

jumper. Connect a cable to pins 4~7 of JD1

to use an external speaker.

Speaker Connector

Pin Defi nitions

Pin Setting Defi nition

Pins 4~7

External Speaker

Pins 6~7

Internal Speaker

PWR LED Connector

Pin Defi nitions

Pin Setting Defi nition

Pin 1

Anode (+)

Pin2 Cathode

(-)

Pin3

IPMB

A System Management Bus header for the

IPMI slot is located at IPMB. Connect the

appropriate cable here to use the IPMB I2C

connection on your system.

IPMB

Pin Defi nitions

Pin# Defi nition

Data

Ground

Clock

No Connection

Video Connector

A Video (VGA) connector is located below

the COM Port on the IO backplane. This

connector is used to provide video and CRT

display.

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды