Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 91

Страница: 91 / 96

Appendix B: Installing Windows

B-1

Appendix B

Installing Windows

After all hardware components have been installed, you must fi rst confi gure RAID

Settings before you install the Windows OS and other software drivers. To confi gure

RAID settings, please refer to RAID Confi guration User Guides posted on our web

site at www.supermicro.com/support/manuals.

Note:

The following OS installation instructions are written for the Windows XP/2003

OS only. If you have the Windows 2008 or Windows Vista OS, please follow the

instructions displayed on your screen to install the OS.

B-1 Installing Windows to a RAID System

Insert Microsoft's Windows XP/Windows 2003 Setup CD in the CD-ROM drive

and the system will start booting up from CD.

Press the <F6> key when the message "Press F6 if you need to install a third

party SCSI or RAID driver" displays.

When the Windows XP/Windows 2003 Setup screen appears, press "S" to

specify additional device(s).

Insert the driver diskette you created in Section 5-11,

Building a Driver

Diskette

, into Drive A: and press the <Enter> key.

Highlight "Manufuacturer Supplied Hardware Support Disk" and hit the

<Enter> key.

Highlight the fi rst "Adaptec RAID" driver shown and press the <Enter> key to

install it. Soon a similar blue screen will appear again.

Again hit the <S> key, then highlight the second item, "nForce Storage

Controller" and press the <Enter> key, then <Enter> again to continue with

the Windows setup.

Press the <Enter> key to continue the installation process. (If you need to

specify any additional devices to be installed, do it at this time.) Once all

devices are specifi ed, press the <Enter> key to continue with the installation.

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды