Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 79

Страница: 79 / 96

Chapter 7: BIOS

7-7

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. Disable Legacy support

if there are no USB devices installed in the system. "Auto" disabled Legacy

support if no USB devices are connected. The options are Disabled, Enabled

and

Auto

IDE Confi guration

Onboard PCI IDE Controller

This setting allows you to

Enable

or Disable the PCI IDE controller.

On Chip SATA Channel

This setting allows you to

Enable

or Disable the OnChip SATA channel.

On Chip SATA Type

Use this setting to set the On Chip SATA type. Options include

Native IDE,

RAID

, AHCI and Legacy IDE.

SATA IDE Combined Mode

This setting allows you to

Enable

or Disable the SATA IDE combined mode.

PATA Channel Confi guration

This allows you to set PATA channel confi guration. Options include

SATA as

Primary

or SATA as secondary.

Primary/Secondary/Third/Fourth IDE Master/Slave

LBA/Large Mode

LBA (Logical Block Addressing) is a method of addressing data on a disk

drive. The options are Disabled and

Auto

Block (Multi-Sector Transfer)

Block mode boosts IDE drive performance by increasing the amount of data

transferred. Only 512 bytes of data can be transferred per interrupt if block

mode is not used. Block mode allows transfers of up to 64 KB per interrupt.

Select "Disabled" to allow the data to be transferred from and to the device

one sector at a time. Select "Auto" to allows the data transfer from and to the

device occur multiple sectors at a time if the device supports it. The options

are

Auto

and Disabled.

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды