Supero SuperServer 1012G-MTF Скачать руководство пользователя страница 44

Страница: 44 / 96

5-10

UPER

ERVER 1012G-MTF User's Manual

System Device

Size

Physical Memory Available
(4 GB Total System
Memory)

Firmware Hub fl ash memory (System BIOS)

1 MB

3.99 GB

Local APIC

4 KB

3.99 GB

Area Reserved for the chipset

2 MB

3.99 GB

I/O APIC (4 Kbytes)

4 KB

3.99 GB

PCI Enumeration Area 1

256 MB

3.76 GB

PCI Express (256 MB)

256 MB

3.51 GB

PCI Enumeration Area 2 (if needed) -Aligned on 256-M
boundary-

512 MB

3.01 GB

VGA Memory

16 MB

2.85 GB

TSEG

1 MB

2.84 GB

Memory available for the OS & other applications

2.84 GB

5-7 Adding PCI Expansion Cards

The SC813MTS-350C chassis can accommodate one full-size PCI-Express or PCI

expansion card with the use of a PCI riser card.

Installing an Add-on Card

After powering down the system, remove the PCI slot shield.

Confi rm that you have the correct riser card for your chassis model and the

add-on card includes a standard bracket.

Remove the chassis cover.

Install the riser card by sliding card into the appropriate riser card in the

serverboard.

Choose the PCI slot shield in which to place the add-on card.

In that slot, open the PCI slot shield lever and slide the shield sideways.

From inside the chassis, remove the PCI slot shield.

Slide the add-on card into the riser card and attach the add-on card bracket

in place of the PCI slot shield.

Secure the add-on card by closing the PCI slot shield lever.

Connect cables to the add-on card as necessary.

10.

Содержание SuperServer 1012G-MTF

































































































Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды

Supero SuperServer 1012G-MTF, Руководство пользователя

Результаты поиска

Содержание SuperServer 1012G-MTF

Отзывы:

Похожие инструкции для SuperServer 1012G-MTF

Бренды по названию

Популярные бренды