Supero SUPER P6DGH Скачать руководство пользователя страница 92

Страница: 92 / 113

BIOS User's Manual

5-18

IRQ14 and 15 will not be available if the onboard PCI IDE is enabled. If all

IRQs are set to ISA/EISA and IRQ14 and 15 are allocated to the onboard

PCI IDE, IRQ 9 will still be available for PCI and PnP devices. This is

because at least one IRQ must be available for PCI and PnP devices. The

settings are PCI/PnP or ISA/EISA.

Reserved Memory Size

This option specifies the size of the memory area reserved for legacy

ISA adapter cards. The settings are Disabled, 16K, 32K or 64K.

Reserved Memory Address

This option specifies the beginning address (in hex) of the reserved

memory area. The specified ROM memory area is reserved for use by

legacy ISA adapter cards. The settings are C0000, C4000, C8000,

CC000, D0000, D4000, D8000 or DC000.

PCI Device Search Order

This option specifies the direction the PCI buses will be scanned. The

settings are First-Last and Last-first.

Default Primary Video

This feature supports multiple displays. The settings are AGP or PCI.

Peripheral Setup

Onboard SCSI

The settings for this option are Enabled or Disabled. When set to

Enabled, this option enables the Adaptec 7896 BIOS.

Remote Power On

Microsoft's Memphis OS supports this feature that can wake-up the

system from a SoftOff state through devices (such as an external

modem) that are connected to COM1 or COM2. The settings are Dis-

abled or Enabled.

CPU1 Current Temperature

The current temperature of CPU1 is displayed in this option.

CPU2 Current Temperature

The current temperature of CPU2 is displayed in this option.

Содержание SUPER P6DGH


















































































































Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды

Supero SUPER P6DGH, Руководство пользователя

Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды