Supero SUPER P6DGH Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 113

background image

1-8

SUPER P6DGH User’s Manual

1-2 PC Health Monitoring

This section describes the PC health monitoring features of the
SUPER P6DGH. It has an onboard Winbond 781D System Hard-
ware Monitor chip that supports PC health monitoring.

Seven Onboard Voltage Monitors for the CPU Cores,
+3.3V,

±±

5V,

and

±±

12V

The onboard voltage monitors scan seven voltages every second.
When running SUPER Doctor or Intel LDCM, once a voltage be-
comes unstable, a warning or an error message will be reported
on-screen. Users can adjust the threshold of the monitored voltage
to determine the sensitivity of the voltage monitor.

Three Fan-Status Monitors with Firmware/Software On/
Off Control

The PC health monitor can check the RPM status of the cooling
fans. The onboard 3-pin CPU fans are controlled by the ACPI BIOS
and the ACPI-enabled operating system. The thermal fan is con-
trolled by the overheat detection logic.

Chassis Temperature Control

The thermal control sensor monitors the real-time chassis tem-
perature. It will turn on the backup fan whenever the chassis tem-
perature exceeds a user-defined threshold. The overheat circuitry
runs independently from the CPU. It can still monitor for overheat
conditions even if the CPU is in sleep mode. Once it detects that
the chassis temperature is too high, it will automatically turn on the
backup fan and trigger the overheat LED (JOH1) and the overheat
buzzer (BZ_ON). The onboard chassis thermal circuitry can monitor
the overall system temperature and alert users when the chassis
temperature gets too high.

«
...
16
17
18
19
20
...
»

Содержание SUPER P6DGH


















































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPER P6DGH

Бренд: P&E Microcomputer Systems Страницы: 59

Бренд: OLIMEX Страницы: 12

Бренд: Gigabyte Страницы: 40

Cypress MB39C502-EVBSK-01

Бренд: Infineon Technologies Страницы: 28

Бренд: ZMDI Страницы: 25

Outboard Motor BF5A

Бренд: Honda Страницы: 84

Бренд: Biostar Страницы: 118

Бренд: Aaeon Страницы: 108

Бренд: Biostar Страницы: 32

Бренд: Systium Technologies Страницы: 4

CAES UT65CML8X8FD-EVB-UM

Бренд: COBHAM Страницы: 20

Бренд: ASROCK Страницы: 106

Бренд: Supermicro Страницы: 107

Бренд: TYAN Страницы: 54

Бренд: TYAN Страницы: 62

Бренд: Dynatem Страницы: 57

Бренд: Intel Страницы: 36

LMQ61460EVM-400K

Бренд: Texas Instruments Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды