Supero SUPER P6DGH Скачать руководство пользователя страница 77

Страница: 77 / 113

Chapter 5: Running Setup

5-3

Date and Time Configuration

Select the Standard option. Select the Date/Time icon. The current

values for each category are displayed. Enter new values with the

keyboard.

Floppy A

Floppy B

Choose the Floppy Drive A or B icon to specify the floppy drive type.

The settings are Not Installed, 360 KB 5¼ inch, 1.2 MB 5¼ inch, 720 KB

3½ inch, 1.44 MB 3½ inch or 2.88 MB 3½ inch. Note: The Optimal

and Fail-Safe settings for Floppy Drive A is 1.44 MB 3 1/2 inch

and for Floppy Drive B is Not Installed.

Advanced Setup

Quick Boot

The settings are Disabled or Enabled. Set to Enabled to permit

AMIBIOS to boot quickly when the computer is powered on. This option

replaces the old "Above 1 MB Memory Test Advanced Setup" option. The

settings are:

Setting

Description

Disabled

AMIBIOS tests all system memory. AMIBIOS waits

for up to 40 seconds for a READY signal from the IDE

hard disk drive. AMIBIOS waits for .5 seconds after

sending a RESET signal to the IDE drive to allow the

IDE drive time to get ready again. AMIBIOS checks

for a <Del> key press and runs AMIBIOS Setup if the

key has been pressed.

Enabled

AMIBIOS does not test system memory above 1 MB.

AMIBIOS does not wait for up to 40 seconds for a

READY signal from the IDE hard disk drive. If a READY

signal is not received immediately from the IDE drive,

AMIBIOS does not configure that drive. AMIBIOS does

not wait for .5 seconds after sending a RESET signal to

the IDE drive to allow the IDE drive time to get ready

again. In Enabled, the keyboard will be bypassed.

Содержание SUPER P6DGH


















































































































Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды

Supero SUPER P6DGH, Руководство пользователя

Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды