Supero SUPER P6DGH Скачать руководство пользователя страница 90

Страница: 90 / 113

BIOS User's Manual

5-16

PCI Latency Timer (PCI Clocks)

This option specifies the latency timings in the PCI clocks for all PCI

devices. The settings are 32, 64, 96, 128, 160, 192, 224 or 248.

PCI VGA Palette Snoop

The settings for this option are Disabled or Enabled. W hen set to

Enabled, multiple VGA devices operating on different buses can handle

data from the CPU on each set of palette registers on every video device.

Bit 5 of the command register in the PCI device configuration space is the

VGA Palette Snoop bit (0 is disabled). For example, if there are two

VGA devices in the computer (one PCI and one ISA) and this option is

disabled, data read and written by the CPU is directed only to the PCI

VGA device's palette registers. If enabled, data read and written by the

CPU is directed to both the PCI VGA device's palette registers and the

ISA VGA palette registers. This will permit the palette registers of both

devices to be identical. This option must be set to Enabled if any ISA

adapter card installed in the system requires VGA palette snooping.

PCI IDE Busmaster

The settings for this option are Disabled or Enabled. Set to Enabled to

specify that the IDE Controller on the PCI bus has bus mastering capabili-

ties. Under Windows 95, you should set this option to Disabled and

install the Bus Mastering driver.

Offboard PCI IDE Card

This option specifies if an offboard PCI IDE controller adapter card is

installed in the computer. The PCI expansion slot on the motherboard

where the offboard PCI IDE controller is installed must be specified. If an

offboard PCI IDE controller is used, the onboard IDE controller is automati-

cally disabled. The settings are Auto (AMIBIOS automatically determines

where the offboard PCI IDE controller adapter card is installed), Slot 1,

Slot 2, Slot 3, Slot 4, Slot 5 or Slot 6.

This option forces IRQ14 and IRQ15 to a PCI slot on the PCI local bus.

This is necessary to support non-compliant ISA IDE controller adapter

cards. If an offboard PCI IDE controller adapter card is installed in the

computer, you must also set the Offboard PCI IDE Primary IRQ and

Offboard PCI IDE Secondary IRQ options.

Содержание SUPER P6DGH


















































































































Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды

Supero SUPER P6DGH, Руководство пользователя

Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды