Supero SUPER P6DGH Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 113

background image

3-5

Chapter 3: Troubleshooting

and enter the filename of the update BIOS image. NOTE: It is im-
portant to save your current BIOS and rename it "super.rom" in case
you need to recover from a failed BIOS update. Select flash boot
block, then enter the update BIOS image. Select "Y" to start the
BIOS flash procedure and do not disturb your system until the flash
utility displays that the procedure is complete. After updating your
BIOS, clear the CMOS and then load the Optimal Values in the BIOS.

Question: After flashing the BIOS my system does not have video.
How can I correct this?

Answer: If the system does not have video after flashing your new
BIOS, the flashing procedure has failed. To remedy this, first clear
the CMOS per the instructions in this manual and retry the BIOS
flashing procedure. If you still do not have video, please use the
following BIOS recovery procedure. Turn your system off and place
the floppy disk with the saved BIOS image file called "super.rom"
(see above FAQ) in drive A. Press and hold "CTRL" and "Home" at
the same time, then turn on the power with these keys pressed until
your floppy drive starts reading. Your screen will remain blank until
the BIOS program is done. If the system reboots correctly, then the
recovery is complete.

Question: I have memory problems. What is the correct memory
to use and which BIOS setting should I choose?

Answer: The correct memory to use on the SUPER P6DGH is 168-
pin DIMM 3.3V non-buffered SPD (Serial Present Detection) SDRAM
and SDRAM. SPD SDRAM is preferred but not necessary. NOTE:
Do not mix memory types; the results are unpredictable. If your
memory count is exactly half of the correct value, go to the BIOS in
the Chipset Setup and set "SDRAM AUTOSIZING SUPPORT" to En-
abled. Change between the available options until one setting dis-
plays the correct size of your memory.

Question: Which Operating System (OS) supports AGP?

Answer: At present, W indows 98 and Windows NT 5.0 are the only
OS's that have built-in support for AGP. Some AGP video adapters
can run Windows 95 OSR2.1 with special drivers. Please contact
your graphics adapter vendor for more details.

Question: Do I need the CD that came with your motherboard?

«
...
66
67
68
69
70
...
»

Содержание SUPER P6DGH


















































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPER P6DGH

Бренд: fadini Страницы: 32

RTKA788152DE0000BU

Бренд: Renesas Страницы: 11

Бренд: ECS Страницы: 60

Бренд: ECS Страницы: 93

Бренд: Texas Instruments Страницы: 13

Бренд: JETWAY Страницы: 39

Бренд: Advantech Страницы: 90

Бренд: Intel Страницы: 113

Бренд: Analog Devices Страницы: 9

Бренд: Analog Devices Страницы: 6

Бренд: Bartels Mikrotechnik Страницы: 9

P35D3 Platinum - Motherboard - ATX

Бренд: MSI Страницы: 104

Бренд: BCM Страницы: 59

Бренд: EVGA Страницы: 128

Бренд: Linear Technology Страницы: 8

Бренд: ASROCK Страницы: 5

Бренд: Zeal-All Страницы: 8

Бренд: Dell Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды