Supero SUPER P6DGH Скачать руководство пользователя страница 110

Страница: 110 / 113

B-7

Appendix B: AMIBIOS POST Diagnostics Error Messages

Check

Point

Description

The programming before WINBIOS Setup has

been completed. Uncompressing the WINBIOS Setup

code and executing the AMIBIOS Setup or W INBIOS

Setup utility next.

Returned from WINBIOS Setup and cleared the screen.

Performing any necessary programming after WINBIOS

Setup next.

The programming after WINBIOS Setup has been

completed. Displaying the power-on screen message

next.

The first screen message has been displayed. The

<WAIT...> message is displayed. Performing the PS/2

mouse check and extended BIOS data area allocation

check next.

Programming the WINBIOS Setup options next.

The WINBIOS Setup options are programmed.

Resetting the hard disk controller next.

The hard disk controller has been reset. Configuring the

floppy drive controller next.

The floppy drive controller has been configured.

Configuring the hard disk drive controller next.

Initializing the bus option ROMs from C800 next.

Initializing before passing control to the adaptor ROM at

C800.

Initialization before the C800 adaptor ROM gains

control has been completed. The adaptor ROM check

is next.

The adaptor ROM had control and has now returned

control to BIOS POST. Performing any required

processing after the option ROM returned control.

Содержание SUPER P6DGH


















































































































Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды

Supero SUPER P6DGH, Руководство пользователя

Результаты поиска

Содержание SUPER P6DGH

Отзывы:

Похожие инструкции для SUPER P6DGH

Бренды по названию

Популярные бренды