Supero SUPER P6DBE Скачать руководство пользователя страница 37

Страница: 37 / 104

UPER P6DBS/P6DBE/P6DBU/P6SBU/P6SBS/P6SBA/P6SBM

Manual

1-28

When Fast SCSI devices are connected, the total length of all cables (internal

and external) must not exceed 3 meters (9.8 ft) to ensure reliable operation. If

no Fast SCSI devices are connected, the total length of all cables must not

exceed 6 meters (19.7 ft).

AIC-7895 consolidates the functions of two SCSI chips, eliminating the need for

a PCI bridge. Reducing PCI bus loading enables system capabilities to be

expanded with additional PCI devices.

The AIC-7895 functions with Adaptec RAIDport II (ARO-1130xA) to deliver RAID

functionality.

1-10 AIC -7890 Ultra II SCSI

Note: If you are using a low voltage differential Hard Drive, it is recommended you use LVD/

SE Ultra II SCSI cable. LVD/SE cable offers increased length, and can accommodate more

d e v i c e s .

SUPER P6DBU/P6SBU has an on-board SCSI controller which is 100% compat-

ible with all major operating and hardware platforms. The AIC-7890 controller

provides advanced PCI-to-SCSI Ultra2 SCSI host adapter features in a 272-pin

Ball Grid Array (BGA) package, as well as containing an integrated dual mode

(LVD/SE) transceiver. The AIC-7890 Ultra2 SCSI chip connects to a 32-bit PCI

bus. It is PCI 2.1 compliant, and fully supports the power management require-

ments specified in Microsoft's PC 97 guidelines and it provides SCAM level 2

support. The AIC-7890 functions with Adaptec RAIDport III (ARO-1130xA-2)

to deliver RAID functionality.

The AIC-7890 Ultra2 SCSI controller, used together with the AIC-3860 trans-

ceiver, allows Ultra2 and single-ended devices to operate together on the same

SCSI bus without inpacting Ultra2 performance and cable lengths. The AIC-7890

controller can support external High Voltage Differential (HVD) transceivers only

for Ultra data rates.

Содержание SUPER P6DBE









































































































Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды

Supero SUPER P6DBE, Руководство пользователя

Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды