Supero SUPER P6DBE Скачать руководство пользователя страница 86

Страница: 86 / 104

BIOS User's Manual

5-20

Serial Port 2 Mode

The settings for this option are

Normal, IrDA

ASK IR

. When set to

IrDA,

the IR Duplex Mode becomes available and can be set to either Half

or Full. When set to

ASK IR,

the IrDA Protocol becomes available and

can be set to 1.6 us or 3/16.

On-Board Parallel Port

This option specifies the base I/O port address of the parallel port on the

motherboard. The settings are

Auto

(AMIBIOS automatically determines

the correct base I/O port address),

Disabled

378

278

3BC

Parallel Port Mode

This option specifies the parallel port mode. The settings are

Normal

Bi-

Dir

EPP

ECP

. When set to

Normal,

the normal parallel port mode is

used. Use

Bi-Dir

to support bidirectional transfers. Use

EPP

(Enhanced

Parallel Port) to provide asymmetric bidirectional data transfer driven by

the host device. Use

ECP

(Extended Capabilities Port) to achieve data

transfer rates of up to 2.5 Mbps. ECP uses the DMA protocol and

provides symmetric

bidirectional communication.

Note: The Optimal

default setting for this option is ECP and the Fail-Safe setting is

N o r m a l

EPP Version

The settings are

Note: The Optimal and Fail-Safe default

settings are N/A.

Parallel Port IRQ

This option specifies the IRQ to be used by the parallel port. The settings

are

Auto

Parallel Port DMA Channel

This option is only available if the setting of the parallel port mode option

ECP

. The settings are

Note: This option is N/

On-Board IDE

This option specifies the onboard IDE controller channels to be used. The

settings are

Disabled, Primary

Secondary

Both

Содержание SUPER P6DBE









































































































Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды

Supero SUPER P6DBE, Руководство пользователя

Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды