Supero SUPER P6DBE Скачать руководство пользователя страница 61

Страница: 61 / 104

3-6

SUPER P6DBS/P6DBE/P6DBU/P6SBU/P6SBS/P6SBA

Manual

Answer: The supplied compact disc has quite a few drivers and programs that

will greatly enhance your system. We recommend that you review the CD and

install the applications you need. Applications included on the CD are PCI IDE

Bus Master drivers for Windows 95 and Windows NT, 440BX chipset drivers for

Windows 95, and Super Doctor Monitoring software.

Question: How do I install an on-board SCSI device controller for my

P6DBS/P6SBS motherboard.

Answer: First install 3 NT installation disks and then follow the on-screen

instructions to complete the procedure. "Safe mode" is best for this installation.

Question: Why can't I turn off the power using the momentary power on/

off switch?

Answer: The instant power off function is controlled by the BIOS. When this

feature is enabled in the BIOS, the motherboard will have instant off capabilities

as long as the BIOS has control of the system. When this feature is disabled

or when the BIOS is not in control, such as during memory count (the first screen

that appears when the system is turned on), the momentary on/off switch must

be held for more than four seconds to shut down. This feature is required to

implement ACPI features on the motherboard.

Question: I see some of my PCI devices sharing IRQs, but the system

seems to be fine, is this correct or not?

Answer: Some PCI Bus Mastering devices can share IRQs without performance

penalties. These devices are designed to work correctly while sharing IRQs.

Question: When I connect my Ultra II LVD Hard Drive on the JA1 SCSI

connection, the drive was not recognized by BIOS or it failed to boot. Do

I need a special cable?

Answer: Yes, for Ultra II LVD Drive, you need a special 68-pin cable with active

termination at the end of the cable, since Ultra II LVD Hard Drive does not have

termination on the drive.

Question: How do I install the sound driver for the built-in ES1938

AudioDrive?

Содержание SUPER P6DBE









































































































Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды

Supero SUPER P6DBE, Руководство пользователя

Результаты поиска

Содержание SUPER P6DBE

Отзывы:

Похожие инструкции для SUPER P6DBE

Бренды по названию

Популярные бренды